| |
Product Image |
Product Name |
Product Descriptions |
|
|
|
|
|
-
A super high-speed tester, capable of performing on every pin using an original algorithm
-
FX-211 can withstand high voltage, up to 100V, and can be embedded in a functional test system
-
Uses semiconductor switches , allow prrogrammable threshold level from 1Ω-1KΩ
-
FX-210 support 128 pins by default, capable of expanding to support 512 pins
-
FX-211 supports 64 pins by default, capable of expanding to support 256 pins.
|
|
|
-
Insulation tester with high voltage support (MAX 200V) to check the isolation resistance (200KΩ to 40MΩ)
-
Best for testing flexible film circuits, such as PC keyboards, mobile phone, keypads, and all types of ceramic-bare circuit boards.
-
Short/Open test capability
-
Super-high speed test performed on each pin using an original test algorithm
|
|
|
-
Best for use in production lines
-
Measurement COM is isolated with digital ground of power supply, COM ports, USB
-
DC voltage, AC voltage, DC current, AC current, resistance, Diode test, etc.
-
Sampling speed can be set in 3 different levels
-
Can be used as test controller
|
|
|
-
Maximum sample rate up to 100MPS with 2 simultaneous channels
-
100MHz bandwidth
-
10 bit high-speed A/D conversion
-
Equivalent sampling, up to 4GPS
-
Equipped with a digital filter. More than 20 types of automatic wave measuring functions allowed
-
Measurement COM is isolated with power and control GND, includes software tools and components (DLL, ActiveX)
|
|
|
-
Maximum 32 channel input, 14-bit resolution data sampling
-
Maximum sampling of 100 KPS (when 4 channels used).
-
Wave memory capacity, up to 25M samples.
-
Long time data recording is available.
-
Wave form measurement and analyze
|
|
|
-
1CH, 2 CH synchronous outputs
-
Frequency, DUTY real-time measurement display functions
-
Output setting backup function
-
Easy operation from front panel
-
Outputs are isolated from controls
|
|
|
-
128 CH digital TTL-level input/output
-
Allow bit control (set preferred bits and keep the other bits)
-
Set byte at output , input , or keep mode
-
Capable of comparing input value with expected value
|
|
|
-
32 photo-coupler input circuit (Triggered LED protection)
-
32 photo-coupler output circuit
-
Allow bit control (set preferred bits and keep the other bits)
|
|
|
-
48 relays, which can be controlled individually
-
Relay can be operated at ON, OFF, ON-OFF-ON and OFF-ON-OFF modes
|
|
|
-
1:32 multiplexer has 4 independent circuits
-
Uses photo MOS relays
-
Up to AC 40V (PEAK) -0.4A signals supported
-
May be combined with the multi meter, the FX-300, and multi-function test module, the FX-700
|
|
|
-
48 relays, which can be controlled individually
-
Relay can be operated at ON, OFF, ON-OFF-ON and OFF-ON-OFF modes
|
|
|
-
48 relays, which can be controlled individually
-
Relay can be operated at ON, OFF, ON-OFF-ON and OFF-ON-OFF modes
|
|
|
- Measurement functions:
20 MPS oscilloscope (WFT), Frequency Counter (FCT), Function Generator (FGT) and Digital Input/Output (DIO), all in 1 unit.
- Test controller function tool (FxAutoTest.exe) included
- Test programs can be saved in the module, capable of executing them without PC connection.
- Test common is isolated from power supply and control GND
|
|
|
-
Convert USB bus into GPIB bus
-
Convert RS-232 into GPIB bus
-
DLL library for FX-910 control included
-
ActiveX components for FX-910 control included
-
Console utility for the GPIB test included
|
